Common M-Codes for Mazak Integrex Machines

We've found it handy to have a quick reference of the M-Codes that are used on our Integrex i250HS machine. Note that there may be other codes available on your machine depending on your build options (ie. lower turret, robot, etc). For further detail on function and syntax, refer to your official Mazak manuals:

"Programming Mazatrol Smooth AI ISO/EIA" - contains your G-codes (see the previous post)

"Parameter Alarm M-Codes" - contains your M-codes

---

Mazak Integrex M-Codes

M-code	Function	Description
M00	Program stop	When this function code is loaded, program execution will be stopped and the PROGRAM STOP indicator lamp will light up. At this time, the milling spindle and the turning spindle will also stop rotating.
M01	Optional stop	To use this function, select (OPTIONAL STOP]. A function similar to that of M00 will be performed. At this time, the milling spindle and the turning spindle will also stop rotating. M01 will be ignored when [OPTIONAL STOP] deselected.
M02	End of program	When this function code is loaded, spindle rotation will be stopped and coolant injection. air blasting and the operation of the oil mist will also be stopped. Finally, the function of the NC unit will be reset tostop all operation. Except in tape operation mode, a function similar to that of M30 is performed (rewind operation).
M03	Start of forward milling spindle rotation	(Upper turret side} This function code rotates the milling spindle forward.
M04	Start of backward milling spindle rotation	(Upper turret side} This function code rotates the milling spindle backward.
M05	Stop of milling spindle rotation	This function code stops the milling spindle whose rotation was started by 11.103 or M04.
M06	Tool change	This function code mounts the specified tool in thespindle and returns the tool of the spindle to the magazine. When a tool is specified as the next tool, the tool is prepared at the ATC arm.
M08	Flood coolant ON	This function code activates the coolant feed unit to inject coolant from the nozzle.
M09	All coolants OFF	This function code turnsoff all machining-related fluids such as coolants and air. M09 must not be preceded by any other coolant command code in the same block. With the YMUK high-pressure coolant specification, pressure selection data will also be cleared.
M19	Milling spindle orientation	This function code orientates the milling spindle of the upper turret to a reference angle and stops the milling spindle there.
M23	Error detect ON	This function code specifies·exact stopping mode". Refer to the operating manual of the NC unit for further details of tne exact stopping mode.
M24	Error detect OFF	This function code cancels M23.
M30	Reset and rewind	This function code stops the machine similarly to M02, resets the function of the NCunit, and returns control to the beginning of the program. The PROGRAM HEAD lamp on the NC screen display lights up.
M48	Cancellation of M49	This function code cancels the override cancel function (M49). The override function, therefore. becomes valid.
M49	Override cancel	This function code cancels the override command. Therefore. the machine operates with program-specified data. Both the feed override and spindle override functions are canceled. Note: When power is switched on or after emergency stop, the NC is (re)set in the M48 mode.
M51	Milling spindle- through coolant ON	This function code activates coolant injection through the milling spindle.
M98	Subprogram call	This function code calls up a subprogram.
M99	Return to main program	The M99 function code denotes the end of the called subprogram. Execution of M99 returns control to the main program.
M100	High-pressure coolant pressure selection 1	This function code selects the 1st level of high-pressure coolant pressure. (YMUK high-pressure coolant interface. YMC super flow}
M101	High-pressure coolant pressure selection 2	This function code selects the 2nd level of high-pressure coolant pressure. (YMUK high-pressure coolant interface. YMC super flow}
M102	High-pressure coolant pressure selection 3	This function code selects the 3rdlevel of high-pressure coolant pressure. (YMUK high-pressure coolant interface. YMC super flow)
M103	High-pressure coolant pressure selection 4	This function code selects the 4th level of high-pressure coolant pressure. (YMUK high-pressure coolant interface. YMC super flow}
M104	High-pressure coolant pressure selection 5	This function code selects the 5th level of high-pressure coolant pressure. (YMUK high-pressure coolant interface. YMC super flow}
M105	High-pressure coolant pressure selection 6	This function code selects the 6th level of high-pressure coolant pressure. (YMUK high-pressure coolant interface. YMC super flow}
M106	High-pressure coolant pressure selection 7	This function code selects the 7th level of high-pressure coolant pressure. (YMUK high-pressure coolant interface. YMC super flow}
M107	B-axis clamping	This function code activates the clamping mechanism of the B-axis.
M108	B-axis unclamping	This function code deactivates the clamping mechanism of the B-axis.
M110	Milling spindle clamp	This function code clamps the clamp mechanism at the end of the milling spindle.
M111	Milling spindle unclamp	This function code unclamps the clamp mechanism at the end of the milling spindle.
M120	Automatic power cutoff	This function code cuts off the main power to the machine when the automatic power cutoff valid/invalid select switch is set to "valid" position.
M129	Flood air blast ON	This function code blows out flood air.
M131	High-pressure coolant ON	This function code activates high-pressure coolant injection.
M132	Milling spindle-through air ON	This function code blows out milling spindle-through air.
M139	Heavy tool mode cancel	This function code cancels heavy tool mode.
M140	Heavy tool mode ON	This function code specifies heavy tool mode.
M149	Magazine rotation	This function code rotates the magazine to index the magazine pocKet specified with T (M)  in M149TM.
M163	Milling spindle- through air OFF	This function code deactivates milling spindle-through coolant or air.
M169	Cancellation of M170	This function code maKes AFC valid. (AFC is usually valid.)
M170	AFC cancel	This function code maKes AFC invalid.
M200	Turning spindle 1 C-axis connecv Milling mode select	This function code connects the turning spindle to the C- axis and changes the mode to milling.
M202	Turning spindle 1 C-axis disconnecv turning mode select	This function code disconnects the C-axis from the turning spindle and changes the mode to turning.
M203	Turning spindle 1 Start of forward rotation	This function code rotates the turning spindleforward.
M204	Turning spindle 1 Start of bacKward rotation	This function code rotates the turning spindlebacKward.
M205	Turning spindle 1 Rotation stop	This function code stops turning spindle rotation.
M206	Turning spindle 1 ChucK open	This function code opens the chucK of the turning spindle.
M207	Turning spindle 1 ChucK close	This function code closes the chucK of the turning spindle.
M210	Turning spindle 1 C-axis clamping	This function code activates the C-axis clamping mechanism to clamp the C-axis when the turning spindleis connecteo to the C-axis.
M211	Turning spindle 1 C-axis braKing	This function code activates the C-axis braKing mechanism to braKe the C-axis when the spindle is connecteo to the C-axis.
M212	Turning spindle 1 C-axis unclamping	This function code deactivates the C-axis clamping mechanism andbraKing mechanism whenthe turning spindle is connected to the C-axis.
M213	Turning spindle 1 C-axis braKing only	When the turning spindle is connected to the C-aXis, the C- axis remains braKed even if C-axis clamping command M210 is given.
M214	Turning spindle 1 C-axis unclamping only	When the turning spindle is connected to the C-axis, the C-axis remainsunclamped even if C-axis clamping command M210 is given.
M215	Cancellation of M214 or M216	This function code cancels the M214/M216 mode.
M216	Turning spindle 1 C-axis unclamping ignore mode ON	When the turning spindle is connected to the C-aXis, the current status of C-axis control is maintained even if C-axis unclamping command M212 is given.
M219	Turning spindle 1 Orientation	This function code orientates the turning spindle to a reference angle and stops it there.
M231	TailstocKforward	This function code moves the tailstocKforward.
M232	TailstocKbacKward	This function code moves the tailstocKbacKward.
M233	Turning spindle 1 ChucKclamp pressure LOW select	This function code changes thegripping pressure of the turning spindle chucK to a low pressure.
M234	Turning spindle 1 ChucKclamp pressure HIGH select	This function code changes thegripping pressure of the turning spindle chucK to a high pressure.
M244	Turning spindle 1 Workpiece washing coolant ON	This function code activates workpiece washing coolant injection on the turning spindle side.
M245	Turning spindle 1 Workpiece washing coolant OFF	This function code deactivates worKpiece washing coolant injection on the turning spindle side.
M248	Parts catcher extend	This function code extends the parts catcher (into the machine).
M249	Parts catcher retract	This function code retracts the parts catcher (out of the machine).
M250	Spindle speed attainment checK	Confirms Whether the specified spindle speed has been attained.
M253	Chamfering OFF	Disables chamfering of threads.
M254	Chamfering ON	Enables chamfering of threads.
M256	Front door open	When a front door automatic open/close option is provided, this function code opens the front door automatically.
M258	Turning spindle 1 ChucK air blast ON	This function code activates turning spindle chucK air blasting. At this time, the turning spindle rotates at about 50 min-'. Air blasting stops after the elapse of the timer-set time.
M264	Turning spindle 1 ChucK jaw coolant ON	This function code activates chucKjaw coolant injection on turning spindle side.
M265	Turning spindle 1 ChucK jaw coolant OFF	This function code deactivates chucK jaw coolant injection on turning spindle side.
M266	Turning spindle 1 Shower coolant ON	This function code activates shower coolant injection on turning spindle side.
M267	Turning spindle 1 Shower coolant OFF	This function code deactivates shower coolant injection on turning spindle side.
M268	Turning spindle 1 Spindle-through coolant ON	This function code activates spindle-through coolant injection on turning spindle side.
M269	Turning spindle 1 Spindle-through coolant OFF	This function code deactivates spindle-through coolant injection on turning spindle side.
M270	Turning spindle 1 Spindle-through air ON	This function code activates spindle-through air on the turning spindle side.
M271	Turning spindle 1 Spindle-through air OFF	This function code deactivates spindle-through air on the turning spindle side.
M272	Turning spindle 1 Internal chucKing	This function code specifies internal gripping for the turning spindle chucK.
M273	Turning spindle 1 External chucKing	This function code specifies external gripping for the turning spindle ChUCK.
M281	Touch sensor ON	This function code turns the touch sensor ON.
M282	Touch sensor OFF	This function code turns the touch sensor OFF.
M283	Tool measurement start	(Upper turret side) This function code extends the TOOL EYE arm for tool measurement.
M284	Tool measurement end	(Upper turret side) This function code retracts the TOOL EYE arm for tool measurement.
M285	Work rest coolant ON	This function code activates coolant feed for the worKrest.
M286	Work rest coolant OFF	This function code deactivates coolant fee<l for the worK rest.
M289	Flooclcoolanv air blasting OFF	This function code deactivates flood coolanVair blasting.
M292	Work rest open	This function code opens the arm of the worK rest.
M293	Work rest close	This function code closes the arm of the worKrest.
M300	Turning spindle 2 C-axis connect - Milling mode select	This function code connects the turning spindle No. 2 to the C-axis and changes the mode to milling.
M302	Turning spindle 2 C-axis disconnect - Turning mode select	This function code disconnects the C-axis from the turning spindle No. 2 and changes the mocle to turning.
M303	Turning spindle 2 Start of forward rotation	This function code rotates the turning spindle No. 2 forward.
M304	Turning spindle 2 Start of backward rotation	This function code rotates the turning spindle No. 2 backward.
M305	Turning spindle 2 Rotation stop	This function code stops rotation of the turning spindle No.2.
M306	Turning spindle 2 ChucK open	This function code opens the chucK of the turning spindle No.2.
M307	Turning spindle 2 ChucK close	This function code closes the chucK of the turning spindle No.2.
M310	Turning spindle 2 C-axis clamping	This function code activates the C-axis clamping mechanism to clamp the C-axis when the turning spindle No. 2 is connecteo to the C-axis.
M311	Turning spindle 2 C-axis braKing	This function code activates the C-axis braKing mechanism to braKe the C-axis when the turning spindle No. 2 is connected to the C-axis.
M312	Turning spindle 2 C-axis unclamping	This function code deactivates the C-axis clamping mechanism anel braKing mechanism when the turning spindle No. 2 is connecte<l to the C-axis.
M313	Turning spindle 2 C-axis braKing only	When the turning spindle No. 2 is connecte<l to the C-axis, the C-axis remains braKe<l even if C-axis clamping command M310 is given.
M314	Turning spindle 2 C-axis unclamping only	When the turning spindle No. 2 is connecte<l to the C-axis, the C-axis remains unclamped even if C-axis clamping command M310 is given.
M315	Cancellation of M314 or M316	This function code cancels the M314/M316 mode.
M316	Turning spindle 2 C-axis unclamping ignore mode ON	When the turning spindle No. 2 is connecte<l to the C-axis, the current status of C-axis control is maintained even if C-axis unclamping command M312 is given.
M319	Turning spindle 2 Orientation	This function code orientates the turning spindle No. 2 to a reference angle and stops it there.
M333	Turning spindle 2 ChucK clamp pressure LOW select	This function coele changes thegripping pressure of the chucK for the turning spindle No. 2 to a low pressure.
M334	Turning spindle 2 ChucK clamp pressure HIGH select	This function coele changes thegripping pressure of the chucK for the turning spindle No. 2 to a high pressure.
M344	Turning spindle 2 Workpiece washing coolant ON	This function coele activates workpiece washing coolant injection for turning spindle No. 2.
M345	Turning spindle 2 Workpiece washing coolant OFF	This function coele deactivates worKpiece washing coolant injection for turning spindle No. 2.
M354	Front door half open	This function coele opens the front door halfway when the auto open/close type front door option is provided. (for 1SOOU specifications only)
M358	Turning spindle 2 ChucK air blast ON	This function coele activates chucK air blasting for the turning spindle No. 2. At this time, the turning spindle rotates at about 50 min-1.Air blasting stops after the elapse of the timer-set time. Timer-set time: PLC parameter TIM76
M364	Turning spindle 2 ChucK jaw coolant ON	This function coele activates chucKjaw coolant injection on turning spindle No. 2 side.
M365	Turning spindle 2 ChucK jaw coolant OFF	This function coele deactivates chucKjaw coolant injection on turning spindle No. 2 side.
M366	Turning spindle 2 Shower coolant ON	This function coele activates shower coolant injection on turning spindle No. 2 side.
M367	Turning spindle 2 Shower coolant OFF	This function cooe deactivates shower coolant injection on turning spindle No. 2 side.
M368	Turning spindle 2 Spindle-through coolant ON	This function coele activates spindle-through coolant injection on turning spindle No. 2 side.
M369	Turning spindle 2 Spindle-through coolant OFF	This function coele deactivates spindle-through coolant injection on turning spindle No. 2 side.
M370	Turning spindle 2 Spindle-through air ON	This function coele activates spindle-through air on turning spindle No. 2 side.
M371	Turning spindle 2 Spindle-through air OFF	This function coele deactivates spindle-through air on the turning spindle No. 2 side.
M372	Turning spindle 2 Internal chucKing	This function cooe specifies internal gripping for the chucK of the turning spindle No. 2.
M373	Turning spindle 2 External chucKing	This function cooe specifies external gripping for the chucK of the turning spindle No. 2.
M400	External M-code output 1	This function coele is sent to an external unit.
M401	External M-code output 2	This function coele is sent to an external unit.
M402	External M-code output 3	This function coele is sent to an external unit.
M403	External M-code output 4	This function code is sent to an external unit.
M404	External M-code output 5	This function coele is sent to an external unit.
M405	External M-code output 6	This function coele is sent to an external unit.
M406	External M-code output 7	This function code is sent to an external unit.
M407	External M-code output 8	This function code is sent to an external unit.
M408	External M-code output 9	This function coele is sent to an external unit.
M409	External M-code output 10	This function coele is sent to an external unit.
M410	External M-code output 11	This function code is sent to an external unit.
M411	External M-code output 12	This function coele is sent to an external unit.
M412	External M-code output 13	This function coele is sent to an external unit.
M413	External M-code output 14	This function code is sent to an external unit.
M414	External M-code output 15	This function coele is sent to an external unit.
M415	External M-code output 16	This function coele is sent to an external unit.
M416	External M-code output 17	This function coele is sent to an external unit.
M417	External M-code output 18	This function code is sent to an external unit.
M418	External M-code output 19	This function coele is sent to an external unit.
M419	External M-coele output 20	This function coele is sent to an external unit.
M503	Tail thrust control mode OFF	This function code cancels the tail axis (W-axis) thrust control mode. (This is executed by an M code macro within the M232 or M843 command.)
M504	Tail thrust control mode ON	This function coele sets the tail axis (W-axis) thrust control mode. (This is executed by an M code macro within the M231, M841 or M842 command.)
M508	Pressing setup	Makes a pressing function effective for delivery of the workpiece from the turning spindle No. 1 to No. 2, or vice versa.
M509	Pushing preparation cancel	This function code cancels the pushing function specified by M508.
M511	Turning spindle synchronized rotation (master. turning spindle No. 1, slave: turning spindle No. 2}	This function coele enables synchronized rotation of two opposite turning spindles.
M512	Turning spindle synchronized rotation (master. turning spindle No. 2, slave: turning spindle No. 1}	This function code enables synchronized rotation of two opposite turning spindles.
M513	Turning spindle synchronized rotation OFF	This function code deactivates M511 and M512.
M540	TRANSFER mode ON	This function code makes the worl<piece transfer mode (from turning spindle No. 1 to turning spindle No. 2 or vice versa) valid.
M541	TRANSFER mode OFF	This function code makes the worl<piece transfer mode (from turning spindle No. 1 to turning spindle No. 2 or vice versa) invalid.
M542	TRANSFER BAR mode ON	This function code makes the worl<piece gripping, synchronized rechucking and synchronized cutting-off modes with both turning spindle No. 1 andturning spindle No. 2 valid.
M543	TRANSFER BAR mode OFF	This function code makes the worl<piece gripping, synchronized rechucking and synchronized cutting-off modes with both turning spindle No. 1 andturning spindle No. 2 invalid.
M557	High-pressure coolant pressure setting cancel	This function code cancels the YMC super flow pressure setting.
M562	Balance cut start	This function code enables the operation of the X1-IZ1-axis of the upper turret in tandem with the X2-IZ2-axis of the lower turret. Note: The turret at which this M code (M562) is executed becomes the main side. A move command must be issued from the main side.
M563	Balance cut end	This function code deactivates M562.
M610	Grinder mode ON	This function code rotates the turning spindle and the milling spindle at the same time andmakes grinder machining function mode valid. At this time, however. the operation of the two spindles is not synchronized.
M611	Grinder milling spindle speed set	This function code sets the milling spindle speed for grinder machining.
M612	Grinder mode OFF	This function code makes M610 invalid.
M613	Mist collector ON	This function code starts the mist collector.
M614	Mist collector OFF	This function code stops the operation of the mist collector.
M619	Milling spindle orient (Work chuck hanel}	(Upper turret side} This function code orients the milling spindle at a speed specified by parameter RS60. Note: To be used when orienting the worl<chuck hand at a low speed.
M660	ISS invalid	This function code disables ISS during automatic operation.
M662	Stock model cutting invalid	This function code makes interference check with stock model invalid so that stock model cutting will not be rendered on the 30  MONITOR display.
M664	Machine interference checK invalid	This function code maKes machine interference checK invalid during automatic operation.
M665	Machine interference checK invalid cancel	This function code cancels the machine interference checK invalid state during automatic operation.
M666	Stoel< model interference checK invalid	This function code maKes interference checK with stocK model invalid.
M667	Stoel< model interference checK invalid cancel	This function code cancels the interference checK with stocK model invalid state.
M668	Fixture model interference checK invalid	This function code maKes interference checK with fixture model invalid.
M669	Fixture model interference checK invalid cancel	This function code cancels the interference checK with fixture model invalid state.
M670	Tool model interference checK invalid	This function code maKes interference checK with tool model invalid.
M671	Tool model interference checK invalid cancel	This function code cancels the interference checK with tool model invalid state.
M687	M688/M689 cancel	This function code maKes M688/689 invalid.
M688	Waiting of cutting start until the next tool is indexed by ATC (coolant injection continued)	This function code disables cutting start before the next tool is indexed by ATC because magazine vibration during ATC operation affects the cutting surface quality. Coolant injection continues at this time. Note: This mode is retained until a reset, emergency stop, or execution of an M687 command.
M689	Waiting of cutting start until the next tool is indexed by ATC (coolant injection stopped)	This function code disables cutting start before the next tool is indexed by ATC because magazine vibration during ATC operation affects the cutting surface quality. Coolant injection stops while the M689 code is effective. Note: This mode is retained until a reset, emergency stop, or execution of an M687 command.
M699	Tool after next preparation	Prepares for the tool change command after the next tool change by setting the specified tool at the carrier.
M703	Chips removal mode (Forward rotation)	This function code rotates the milling spindle in the forward direction at a speed specified by parameter RS14. (The forward rotation time is determined by parameter TIM78.)
M704	Chips removal mode (Reverse rotation)	This function code rotates the milling spindle in the reverse direction at a speed specified by parameter RS14. (The reverse rotation time is determined by parameter TIM78.)
M706	Work chucK hand open	This function code opens the work chucK hand.
M707	Work chucK hand close	This function code closes the worKchucKhand.
M720	Robot workpiece service request	This function code sends a service request to the robot.
M721	Robot workpiece service request	This function code sends a service request to the robot.
M722	Robot workpiece service request	This function code sends a service request to the robot.
M723	Robot workpiece service request	This function code sends a service request to the robot.
M724	Robot workpiece service request	This function code sends a service request to the robot.
M725	Robot workpiece service request	This function code sends a service request to the robot.
M726	Robot workpiece service request	This function code sends a service request to the robot.
M727	Robot workpiece service request	This function code sends a service request to the robot.
M728	Robot workpiece service request	This function code sends a service request to the robot.
M729	Robot workpiece service request	This function code sends a service request to the robot.
M730	Milling spindle retraction position	This function code moves the milling spindle to the wait position to allow the GL arm to enter the machine.
M731	W-axis retraction position	This function code moves the W-axis to the wait position to allow the GL arm to enter the machine.
M734	GL control axis interlocKvalid	This function code interlocKsthe GL control axis.
M735	GL control axis interlocKrelease	This function code releases the GL control axis interlocK.
M755	Spare send signal ON	This function code turns ON the spare send signal to the bar feeder.
M768	Bar feeder call 1	This function code requests bar feeder service.
M769	Bar feeder call 2	This function code requests bar feeder service.
M838	Correction update stop	This function code stops reception of thermal displacement correction data.
M839	M838 cancel	This function code cancels the thermal displacement correction update stop function specified with M838.
M840	Tailstock thrust setup	This function code changes the thrust of the tailstocKto an arbitrary value.
M841	TailstocK movement to position 1	This function code moves the tailstock to TAIL POS.1 specified in the setup data.
M842	TailstocK movement to position 2·	This function code moves the tailstock to TAIL POS.2 specified in thesetup data.
M843	TailstocK movement to Reverse Position·	This function code moves the tailstocKto the position 50 mm retracted from the current position.
M844	TailstocKinterlocK release	This function code allows spindle rotation, regardless of the current position of the tailstock.
M845	Cancellation of M844	This function code cancels the M844 mode.
M870	Axis load detection invalid	This function code maKes load detection invalid for the axis specified in thesecond auxiliary code A*..  that follows M870.
M871	Axis load detection valid	This function code starts load detection based on data of the axis and table number specified in the second auxiliary code A*-   that follows M871.
M872	Axis load detection temporarily invalid	This function code makes temporarily invalid the load detection that has been started by the execution of M871.
M873	Axis load detection restart	This function code restarts the load detection that has been stopped by the execution of M872.
M874	Overload process selection (NC feed hold)	This function code brings the machine into an NC feed- hold stop when an overload is detected.
M875	Overload process selection (NC feed hold & spindle stop)	When an overload is detected, this function code brings the machine into an NC feed-hold stop and a turning spindle (milling spindle) stop. After resetting the NC is set in this mode.
M876	Overload detection level % setup	This function code sets the overload detection level at the value specified in the second auxiliary code A.-   that follows M876. The specified value is registered under the table number specified in M879A-*.
M877	Overload detection time setup (in 0.1 sec)	This function code sets the overload detection time at the value specified in the second auxiliary code A.-   that follows M877. The specified value is registered under the table number specified in M879A-*.
M878	Overload detection peak level % / Detection count setup	This function code sets the overload peak/detection count reference data according to the value specified in the second auxiliary code A*** that follows M878.
M879	Overload detection data table no. registration	This function code registers M876 - M878 data settings under the table number specified in the second auxiliary code.
M894	Spindle tool number memory clear	This function code clears the spindle tool number memory inside the PLC.
M901	HD1 spindle selection	This function code selects the HD1 turning spindle for machining With the upper or lower turret. Note: The headstock must be selected for both the TR1 and TR2 program sections.
M902	HD2 spindle selection	This function code selects the HD2 turning spindle for machining with the upper or lower turret. Note: The headstock must be selected for both the TR1 and TR2 program sections.
M950	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M951	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M952	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M953	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M954	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M955	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M956	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M957	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M958	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M959	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M960	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M961	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M962	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M963	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M964	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M965	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M966	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M967	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M968	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M969	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M970	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M971	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M972	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M973	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M974	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M975	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M976	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M977	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M978	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M979	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M980	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M981	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M982	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M983	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M984	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M985	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M986	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M987	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M988	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M989	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M990	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M991	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M992	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M993	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M994	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M995	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M996	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M997	Standby code	This function code enables machining operation by synchronizing the TR1 program with the TR2 program at a specified position.
M998	Program chain (WNo. search Cycle Start)	Regarded as theenel of the program, and cyclically starts the next program after executing the number search for the program.
M999	Program chain (WNo. Search Only)	Regarded as theenel of the program, and terminates operation with the number search for the next program.

---

Hopefully these are useful and help to increase your understanding and efficiency!